Cycle Accessory Store

CB Antenna Kit for Honda GL-1500

CB Antenna Kit for Honda GL-1800

This is a direct plug-and-play adapter harness to connect the Beltronics RX65 radar detector to the J&M CFRG units (Cell Phone/GPS/Radar) or other applicable J&M integration/system modules.

This cell phone adapter harness for the JCB03-CFRG-D integration terminal features the 2.5mm 3-conuctor plug for standard cell phones jacks, along with the 3.5mm 4-conductor plug for Blackberry/I-phone, and other cell phones utilizing the 3.5mm 4-conductor jack.

This cell phone/Motorola T-series FRS adapter harness for the JCB03-CFRG-D integration terminal features the 2.5mm 3-conuctor plug for standard cell phones jacks, along with the 3.5mm 4-conductor plug for Blackberry/I-phone, and other cell phones utilizing the 3.5mm 4-conductor jack. The third special plug on this harness is spec’d for the Motorola T-series FRS two-way radios utilizing the special single plug-jack design for remote speaker/mike connection.

This combination Garmin® Zumo550(ONLY)/Motorola T-series FRS adapter harness for the JCB03-CFRG-D integration terminal features the 2.5mm 2-conductor plug for the mike-in jack on the Zumo550 mounting cradle, along with the 3.5mm 3-conductor plug for the audio-out jack on the Zumo550 mounting cradle. The third special plug on this harness is spec’d for the Motorola T-series FRS two-way radios utilizing the special single plug-jack design for remote speaker/mike connection. Harness kit also includes the handlebar-wrap PTT switch for proper operation of the FRS radio.

This Garmin® Zumo660 (ONLY) adapter harness for the JCB03-CFRG-D integration terminal features the 2.5mm 2-conductor plug for the mike-in jack on the Zumo660 cable leads, along with the 3.5mm 3-conductor plug for the audio-out jack on the Zumo660 leads.

This combination Garmin® Zumo660 (ONLY) & Motorola T-series FRS adapter harness for the JCB03-CFRG-D integration terminal features the 2.5mm 2-conductor plug for the mike-in jack on the Zumo660 cable leads, along with the 3.5mm 3-conductor plug for the audio-out jack on the Zumo660 cable leads. The third special plug on this harness is spec’d for the Motorola T-series FRS two-way radios utilizing the unique single plug-jack design for remote speaker/mike connection. Harness kit also includes the handlebar-wrap PTT switch for proper operation of the FRS radio.

This component terminal will integrate the audio signals from a cell phone, GPS and/or radar detector with the driver's (only) helmet headset on a 1998 - Now Harley Ultra.  If the cell phone normally rings out of its hands-free headset jack, or emits any other beeps or tones, it will momentarily be heard in the left headset speaker. A flip of the supplied control switch activates complete connection of the driver's headset to the cell phone for complete hands-free operation.  If the radar detector or GPS unit emit any commands, beeps or braps, regardless of what else might be being heard in the headset, they will momentarily be heard in the right speaker.

This kit includes the plug-in integration module, handlebar-mounted control switch, adapter cables for three-pin and four-pin cell phone headset jacks along with the new adapter cable for the I-phone/Blackberry, and complete installation and operating instructions.

Note: Additional GPS/Radar cable adapters/accessories are available (at extra cost) for a complete plug-and-play solution.

This is a direct plug-and-play adapter harness to connect the Passport 8500 radar detector to the J&M CFRG units (Cell Phone/GPS/Radar) or other applicable J&M integration/system modules.

This is a direct plug-and-play adapter harness to connect the Valentine One radar detector to the J&M CFRG units (Cell Phone/GPS/Radar) or other applicable J&M integration/system modules. (Valentine remote head not needed)

Headset volume of the radar beeb/brap signal is adjusted with the small screw on the harness adapter.

This is a direct plug-and-play adapter harness to connect the Whistler XTR radar detector to the J&M CFRG units (Cell Phone/GPS/Radar) or other applicable J&M integration/system modules.

Note: Make sure that your Whistler radar detector has an external speaker jack built into it as parts of it’s design.